Setting up A Bathtub
Setting up A Bathtub
Blog Article
In this article in the next paragraph you can locate a bunch of reliable expertise concerning How to Install a Bathtub: Install an Acrylic Tub and Tub Surround.
Installing a tub isn't specifically brain surgery, but it does need strong plumbing, carpentry, as well as often, tiling abilities. Replacing an old tub with a brand-new one is additionally a moderately difficult job. If the old bathtub is conveniently accessible, the project can move rapidly; if you need to open up a wall surface to remove the old tub as well as position the brand-new tub, the job is a lot harder. In either instance, the task is within a home handyman's skills, although you will require an assistant to vacate the old bathtub as well as embeded in the brand-new one. See to it you have qualified yourself for the task as well as fit trying it. As opposed to hiring a contractor to take control of a halfway-completed project, it is better to consider employing one before you begin. Chances are you may need a professional plumber to make tube connections.
This short article will assist you set up a new tub in your restroom if you have already gotten a brand-new tub and don't need to change the arrangement of your previous water supply pipes.
Your tools and also product checklist ought to comprise the following:
Removing Old Taps
If you require to change old faucets with new ones as a part of your setup, then the first thing you should do is disconnect the water supply. After doing so, activate the faucets to drain any type of water remaining in the system. The procedure of getting rid of the existing faucets can be rather troublesome due to the restricted accessibility that is typically the situation.
Use a container wrench (crowsfoot spanner) or a faucet tool to undo the nut that connects the supply pipelines to the faucets. Have a fabric ready for the continuing to be water that will certainly come from the pipes. As soon as the supply pipelines have been removed, make use of the exact same tool to loosen up the nut that holds the taps onto the bath/basin. You will require to stop the single faucets from turning throughout this procedure. When the taps have actually been eliminated, the holes in the bath/basin will need to be cleaned up of any old securing substance.
Prior to proceeding to fit the brand-new faucets, compare the pipeline connections on the old faucets to the brand-new taps. If the old faucets are longer than the new taps, after that a shank adapter is required for the brand-new taps to fit.
Suitable New Touches
If the tails of the new faucets are plastic, then you will certainly need a plastic adapter to avoid damages to the string. One end of the connector fits on the plastic tail of the faucet as well as the various other end offers a connection to the existing supply pipelines.
If you need to fit a monobloc, after that you will require minimizing couplers, which connects the 10mm pipeline of the monobloc to the basic 15mm supply pipeline.
Next, place the tap in the placing hole in the bath/basin making certain that the washers are in location in between the tap and also the sink. Secure the tap in position with the maker given backnut. Once the faucet is securely in place, the supply pipelines can be attached to the tails of the taps. The taps can either be linked by utilizing corrugated copper piping or with normal tap adapters. The previous type must be attached to the tap ends initially, tightening just by hand. The supply pipelines can later be connected to the various other end. Tighten both ends with a spanner after both ends have actually been linked.
Mounting the Bathtub
Making use of the two wooden boards under its feet, position the bathtub in the needed setting. The wood boards are helpful in evenly spreading out the weight of the bath tub over the area of the boards rather than concentrating all the weight onto 4 small points.
The following objective is to ensure that the bathtub is leveled all round. This can be achieved by inspecting the level and adjusting the feet on the tub till the spirit level checks out degree.
To mount taps, fit the bottom of the outermost flexible tap connector to the suitable supply pipeline by making a compression join; then do the exact same for the various other faucet.
Activate the water and also examine all joints and new pipework for leaks and tighten them if essential. Fill the bathtub and likewise examine the overflow outlet and the normal outlet for leaks.
Lastly, repair the bathroom paneling as defined in the supplier's user's manual. Tiling and also securing around the bath tub must wait till the bath tub has actually been utilized at the very least when as this will certainly resolve it right into its final setting.
Getting ready for the Installation
Firstly, the sustaining structure provided with the bathroom must be fitted (if needed) according to the maker's directions. Next, fit the taps or mixer to the bath tub. When suitable the faucet block, it is very important to make certain that if the tap comes with a plastic washer, it is fitted in between the bathroom as well as the taps. On a plastic bath, it is also reasonable to fit a sustaining plate under the taps unit to prevent pressure on the tub.
Fit the flexible faucet adapters to the bottom of both faucets utilizing 2 nuts as well as olives (in some cases supplied with the tub). Fit the plug-hole electrical outlet by smearing mastic filler round the sink electrical outlet opening, and after that pass the outlet through the hole in the bathroom. Make use of the nut provided by the maker to fit the plug-hole. Analyze the plug-hole outlet for an inlet on the side for the overflow pipeline.
Next off, fit the end of the flexible overflow pipe to the overflow electrical outlet. Afterwards, screw the pipe to the overflow face which ought to be fitted inside the bath. See to it you make use of every one of the supplied washers.
Attach the catch to the bottom of the waste outlet on the bathtub by winding the string of the waste electrical outlet with silicone mastic or PTFE tape, and screw on the trap to the electrical outlet. Link the bottom of the overflow tube in a comparable manner.The bath should currently be ready to be fitted in its last setting.
Tiling Around the Bathtub
In the location where the bathroom meets the floor tile, it is essential to seal the joins with a silicone rubber caulking. This is necessary as the installation can move sufficient to break a rigid seal, creating the water to permeate the wall in between the bath and also the tiling, causing problems with wetness as well as possible leakages to the ceiling below.
You can pick from a range of coloured sealers to assimilate your fixtures as well as fittings. They are marketed in tubes as well as cartridges, and also are capable of sealing spaces up to a size of 3mm (1/8 inch). If you have a larger void to fill, you can load it with twists of drenched newspaper or soft rope. Bear in mind to always load the tub with water prior to sealing, to permit the movement experienced when the bathtub is in usage. The sealant can split fairly very early if you do not consider this activity before securing.
Alternatively, ceramic coving or quadrant ceramic tiles can be used to edge the bathroom or shower tray. Plastic strips of coving, which are easy to use and reduce to size, are likewise conveniently offered on the marketplace. It is recommended to fit the floor tiles using waterproof or water-proof adhesive and also grout.
How to Install or Replace a Bathtub
Find Your Dimensions
The first step in any bathtub installation or replacement is to select the right size tub for your bathroom. Start by measuring your existing bathtub’s alcove from wall to wall. The standard size for bathtubs is around 5 feet long and 30 or 32 inches wide. Purchase the size that’s closest to your previous tub.
After you’ve measured, you’ll need to figure out what type of tub you need. Face the alcove. If the drain is on the right-hand side, you’ll need a right drain tub. If it’s on the left, get a left drain tub. Easy enough, right?
Disconnect the Water Supply and Drain Assembly
Before you can start on your removal, make sure that you turn off the tub’s water supply. Some bathrooms have a shutoff valve, but if you don’t see one, you’ll need to turn off the supply at your house’s water main. Once the water’s off, open the valves to release any remaining air in the supply lines.
Then, disconnect the tub drain flange. This process varies based on the type of drain you have, but in most cases, you’ll need a drain flange removal tool to perform this task. If you’re feeling handy, you might be able to use a pair of needle-nose pliers to twist and pull the flange.
Now comes the fun part. In order to disconnect the drain assembly, you’ll need to be able to get to the space underneath the tub. You might need to access the tub drain from a crawlspace or a basement. Don’t forget to take a pipe wrench with you, as you’ll need it to loosen the pipe at the connection.
Cut Out the Old Tub
After removing the drainpipe assembly, you can take out the old bathtub. Cut a strip above the tub edge in the wall surrounding the bathtub that's about 6 inches in height. The tools you need here may vary depending on the type of wall surround you have in the alcove. If you’re cutting drywall, use a drywall saw and remove the section of the wall all the way down to the studs. If you have tile, you’ll need to use a grinder with a diamond blade to cut through the grout line. Then, use a chisel to remove the individual tiles. Take care here not to cut through any studs.
Find the tub flange. Remove the screws that attach the flange to the studs in the wall. At this point, the tub should be freed from the wall.
Once you’ve removed the flange, use a utility knife to cut away the caulk between the tub and the floor. When this is done, you should be able to lift the tub up and out of the alcove. Keep in mind that, depending on what it’s made of, the old tub could be tremendously heavy. You should plan to have a friend help you move it just in case.
Install the New Tub
Before you make any adjustments to the area, place the new tub in the alcove to make sure it fits properly and that the tub drain lines up with the P-trap underneath the floor.
Remove it and install a 2 x 4 ledger board. Measure the tub’s flange, then mark that height on the wall. Screw the ledger board to studs in the wall. This will help to support the weight of the tub.
Once the ledger board has been installed, go ahead and secure the drain to the tub. For this step, you’ll need some plumber’s putty. Roll a small amount of putty in your hands and wrap it around the underside of the drain flange. Push the drain into the tub from underneath the tub.
When the drain has been attached, connect the overflow drain. To do this, you’ll place the gasket on the overflow elbow and move it behind the tub. Once that’s on, connect the overflow pipe and the drainpipe, but take care not to overtighten.
Secure the Tub
After the connections are in, it’s time to set the tub in place. Before you start, make sure the flange lines up with the markings you made in Step 4. Because the ledger board holds the tub in place, it’s important that it matches up. If not, you’ll need to remove it and readjust.
Once your measurements line up, attach the flange to the studs on all three sides of the wall. Please note that you should not screw the flange to the wall. Instead, you should use roofing nails because they won’t rust over time. When the tub is in place, install the baseboard and the molding in front of and around the tub.
Repair and finish off the drywall or tile that you cut in Step 3. If you’re installing a fiberglass bath surround, now’s the time to adhere it to the alcove.
Then, enjoy your tub! While all these steps might seem intimidating, removing and installing a new bathtub is a relatively easy DIY project that can be completed in a single day. And now, when you settle in for your next bubbly soak, you can enjoy your bath without the distraction of a tub in disrepair.
https://www.homeserve.com/en-us/blog/how-to/bathtub-replacement/
We are very interested in How to Install a Bathtub: Install an Acrylic Tub and Tub Surround and I really hope you liked the post. Those who appreciated our article if you please make sure you remember to pass it around. Bless you for your time. Visit us again soon.
Request An Appointment
Report this page